home *** CD-ROM | disk | FTP | other *** search
/ Tech Arsenal 1 / Tech Arsenal (Arsenal Computer).ISO / tek-20 / pmb.zip / TNC2CMDS.SET < prev    next >
Text File  |  1990-10-14  |  8KB  |  130 lines

  1.  
  2.                               *** TNC2 COMMANDS *** 
  3.  
  4.  
  5. 8bitconv OFf   High-order bit stripped in CONVers mode (ON- bit not stripped)
  6. AUtolf   ON    <LF> sent to terminal after each <CR> (OFf- <LF> not sent)
  7. AWlen    7     Number of data bits per word to terminal (7 or 8)
  8. Ax25l2v2 OFf   AX.25 Level 2 Version 1.0 (ON- Version 2.0)
  9. AXDelay  0     Wait time in 10ms intervals in addition to TXdelay (0 - 180)
  10. AXHang   0     Audio repeater 'hang time' in 100ms intervals (0 - 20)
  11. Beacon   Every 0    Send beacon in (n * 10s) intervals (0 - 250)
  12.          After n    Send beacon once after (n * 10s) of no activity (0 - 250)
  13. BELL     ON    When ON, a CTRL-G will ring your computers bell         
  14. BKondel  ON    <BS><SP><BS> echoed in response to ^H (OFf- <\> echoed)
  15. BText          Text to be sent for Beacon (120 char max)(% or & clears BText)
  16. BUdlist  OFf   Ignore packets from stations IN LCAlls (ON-Ignore packets from
  17.                stations NOT in LCAlls)
  18. CALibra        Tranfer control to calibration routines. (<SP>,D,K,Q)
  19. CALSet   n     Specify count set [(n=(525,000/f)+1]-modulate
  20.                [(262,500/f)+1]-demodulate
  21. CANline $18 <^X>   Character to cancel input since last <CR> ($00 - $7F)
  22. CANPac  $19 <^Y>   Character to cancel input since last packet ($00 - $7F)
  23. CHeck    30    Time in 10s intervals to check for disconnect (0 - 250)
  24. CLKADJ   0     Correction factor for real-time clock (0 - 65535)
  25. CMdtime  1     Transparent timeout in seconds - used for 'break' (0 - 250)
  26. CMSg     OFf   CText not sent (ON-CText sent after connection by another TNC)
  27. COMmand  $03 <^C>  Character to enter command mode from CONVers ($00 - $7F)
  28. CONMode  Convers   Automatically enters Convers on connection (Trans-)
  29. Connect  call1 [Via call2[,call3[,...,call9]]]
  30. CONPerm  OFf   Current stream may be connected to and disconnected from (ON-)
  31. CONOk    ON    Connect requests accepted from other TNCs (OFf- Not accepted)
  32. CONStamp OFf   Connect status messages not time stamped (ON-Are time stamped)
  33. CONVers        Enter CONVers mode from Command mode (alternate- K)
  34. CPactime OFf   Packets not sent according to PACTime in CONVers mode (ON-)
  35. CR       ON    SEndpac character sent along with packet (OFf- not sent)
  36. CStatus        Shows stream id and link status of all ten streams           
  37.                (...P- Permanant)
  38. CText          Text sent on Connect if CMSg ON (120 char max- %, & to clear)
  39. DAytime  yymmddhhmm     Set current date and time in 24 hour format
  40. DAYUsa   ON    Date display format: mm/dd/yy (OFf-European format: dd-mm-yy)
  41. DELete   OFf   Delete character is <BS> or $08 (ON- <DEL> or $7F)
  42. DIGipeat ON    TNC will digipeat packets on request (OFf- will not digipeat)
  43. Disconne       Initiate Disconnect sequence (Second one will disconnect
  44.                immediately without waiting for acknowledge packet)
  45. DISPlay        Display all control parameters and their current values
  46.          Async         Synchronous port parameters
  47.          Characte      Special characters
  48.          Id            ID parameters
  49.          Link          Link parameters
  50.          Monitor       Monitor parameters
  51.          Timing        Timing parameters
  52. DWait    16    Wait time in 10ms intervals after last activity (0 - 250)
  53. Echo     ON    Characters received echoed by TNC (OFf- Not echoed)
  54. FILter   OFF   Filters out CTRL characters when ON 
  55. FRack    4     Frame acknowledge wait in 1s intervals (1 - 15) Retry
  56.                interval(sec)=n*(2*[# of relay stations]+1)
  57. FUlldup  OFf   Full duplex mode disabled -DCD used (ON- Full duplex enabled)
  58. HEaderln OFf   Header on line with monitored packet text (ON- Seperate lines)
  59. HId      OFf   (ON- ID packet every 9.5 minutes IF station is digipeating)
  60. Id             Sends special ID packet from command mode
  61. K              Equivalent of CONVers (undocumented)
  62. LCAlls [call1[,call2[,...call8]]] Call list for BUdlist (& and % to clear)
  63. LCok     ON    Lower case characters sent to terminal (OFf- Only upper case)
  64. LCStream ON    Case of Charac after STReamsw char not significant (OFf-signif)
  65.                PK-80 command only
  66. LFadd    OFf   <LF> character not sent with each <CR> in packet             
  67.                (ON- <LF> sent)
  68. MAll     ON    All monitored packets displayed if Monitor is ON (OFf- Only
  69.                'unconnected' packets displayed)
  70. MAXframe 4     Number of unacknowledged packets allowed (1 - 7)
  71. MCOM     OFf   Only information packets monitored; <C>, <D>, <UA> and <DM>
  72.                frames not monitored (ON- All are monitored)
  73. MCon     ON    Monitor mode enabled when TNC is connected (OFf- Disabled)
  74. MFilter  $00[,n2[,n3[,n4]]] Characters to be filtered by TNC ($00 - $7F)
  75. MHClear        Clears MHeard list
  76. MHeard         Lists last 20 calls with date (* indicates heard thru digi)
  77. Monitor  ON    Enables general packet monitoring (OFf- Disables)
  78. MRpt     ON    Display digipeat path for monitored packets (OFf- Only display
  79.                origin and destination stations)
  80. MStamp   OFf   Monitored frames are not time stamped (ON- each time stamped)
  81. MYcall   NOCALL[-n]  Your call sign (optional -n: 0 - 15)
  82. MYAlias  call[-n]    Alternate call sign for use as digipeater (-n: 0 - 15)
  83. NEwmode  OFf   Switch on to CONVers or Trans mode on connection only (ON-
  84.                Switching to data transfer mode occurs at time of Connect
  85.                command AND returns to command mode after disconnect)
  86. NOmode   OFf   Mode switching determined by NEwmode (ON- switches by user
  87.                command only) PK-80 command only
  88. NUcr     OFf   Null characters not sent to terminal after <CR> (ON- Sent)
  89. NULf     OFf   Null characters not sent to terminal after <LF> (ON- Sent)
  90. NULLs    0     Number of nulls to sent after <CR> or <LF> (0 - 30)
  91. Paclen   128   Maximum length of data part of packet (0 - 255, 0=256)
  92. PACTime  After 10   Input bytes sent after n*100 ms with no input (0 - 250)
  93.         (Every n    Input bytes sent every n*100 ms - No zero length packets)
  94. PARity   3     Parity bit setting to terminal (0- or 2- none; 1- odd; 3- even)
  95. PASs    $16 <^V>  Input character following this one is sent without being
  96.                interpreted as a command ($00 - $7F)
  97. PASSAll  OFf   TNC only accepts packet with valid CRC (ON-Accepts any packet)
  98. RECOnnect      Change connection path while connected: Argument per Connect
  99. REDispla $12 <^R>  Character to redisplay last input line ($00 - $7F)
  100. RESET          Resets all parameters to TAPR default settings
  101. RESptime 12    Minimum delay (n*100ms) until acknowledge packet sent (0 - 250)
  102. RESTART        Reinitializes TNC to user default settings in bbRAM
  103. REtry    10    Maximum number of packet retries (0 - 15; 0 - infinite retries)
  104. Screenln 80    Number of bytes sent to terminal before extra <CR><LF> is sent
  105.                (0 - 255; 0 - disable)
  106. SEndpac $0D <^M>  Character to force packet to be sent ($00 - $7F)
  107. STArt   $11 <^Q>  Input character to restart output from TNC after STOp
  108.                   ($00 - $7F)
  109. STOp    $13 <^S>  Input character to stop output from TNC to terminal
  110.                   ($00 - $7F)
  111. STREAMCa OFf   Call sign of other station not displayed (ON- )
  112. STREAMDb OFf   Do not double all RECEIVED switch characters (ON- Double)
  113. STReamsw $7C <|>  Stream switch character ($00 - $7C)
  114. TRACe    OFf   (ON- Display trace mode with hex, shifted ASCII and ASCII)
  115. Trans        rol only for terminal (ON- XON/XOff enabled in
  116.                transparent mode)
  117. TRIes    n     Current number of REtry level (0 - 15)
  118. TXdelay  30    Wait time after key up before sending packet n*10ms (0 - 120)
  119. TXFlow   OFf   Hardware control only for TNC (ON- XON/XOff enabled in
  120.                transparent mode)
  121. Unproto  call1[Via call2[,...call9]]  TO address of unconnected packets (CQ)
  122. USers    1     Number of active input connections allowed (0 - 10; 0=10)
  123. Xflow    ON    XON/XOff software flow control enabled (OFf- Disabled)
  124. XMitok   ON    Transmit enabled (OFf- Disabled)
  125. XOff    $13 <^S>  Character output by TNC to stop terminal input ($00 - $7F)
  126. XON     $11 <^Q>  Character output by TNC to start terminal input ($00 - $7F)
  127.  
  128.                            -----------E N D----------
  129.  
  130.